DOI: 10.25881/20728255_2026_21_4_93

Authors

Spirin O.A., Aganesov A.G., Aleksanyan M.M., Presnyakov E.V., Dalgatov M.G.

Petrovsky National Research Center of Surgery Institute», Moscow

Abstract

Rationale: Implants used in clinical practice can be a common factor for transmitting hospital-acquired infections. Polymer materials depending on the chosen sterilization method may change their properties and structures and have toxic effects on the human body. The optimal method of sterilizing biological implants remains an important topic for modern medical community.

Purpose: To study types of medical sterilization methods for biological implants and compare obtained results.

Materials and Methods: In this work, films were made from polymer material (L-lactide-co-e-caprolactone). Obtained samples were sterilized using two cycles of gas sterilization at temperatures of 38 °C and 55 °C. For evaluation of gamma radiation influence, rods of identical polymer material were used as specimens.

Results: After undergoing sterilization at 55 °C, all lactide-based and e-caprolactone films slightly increased in size with thickness increasing by 1-5 microns, which is less than statistical variation values. For polymers subjected to most commonly applied dose of gamma irradiation – 25 kGy – a decrease in molecular mass by 20–25% was observed.

Conclusions: Consistency of parameters indicates suitability of ethylene oxide sterilization for polymer materials based on lactides. Gamma sterilization method could be utilized when initial polymer has sufficiently high molecular weight.

Keywords: degenerative-dystrophic diseases of the spine, disc herniation, spinal stenosis, biodegradable cervical cage.

References

1. Herczeg CK. Sterilization of Polymeric Implants: Challenges and Opportunities. Appl Bio Mater. 2023; 5(11): 5077-5088.

2. Bento CSA, et al. A review of conventional and emerging technologies for hydrogels sterilization. Int. J. Pharm. Elsevier B.V. 2023; 634: 122671.

3. Rozanov VV, Matveichuk IV. The current state and promising innovative directions to development methods for bioimplant sterilization. Almanakh of clinical medicine. 2019; 47(7): 634–646. (In Russ.)

4. Sara P, et al. How to Sterilize Polylactic Acid Based Medical Devices ? Polymers (Basel). 2021; 13(2115): 1-18.

5. M Z, et al. The Influence of the Steam Sterilization Process on Selected Properties of Polymer Samples Produced in MEX and JMT Processes. Materials (Basel). 2024; 17(5763): 1-14.

6. Marques AC, Costa PC. Effects of Steam Sterilization on the Properties of Stimuli-Responsive Polymer-Based Hydrogels. Gels. 2023; 9(385): 1-16.

7. Sara P, et al. 3D-Printed PLA Medical Devices : Physicochemical Changes and Biological Response after Sterilisation Treatments. Polymers (Basel). 2022; 14(4117): 1-20.

8. Harrell CR, et al. Risks of Using Sterilization by Gamma Radiation : The Other Side of the Coin. Int. J. Med. Sci. 2018; 15: 274-279.

9. McGown RG. Ethylene oxide sterilisation. Anaesthesiu. 1972; 27(2): 237.

For citation

Spirin O.A., Aganesov A.G., Aleksanyan M.M., Presnyakov E.V., Dalgatov M.G. Impact of sterilization on the properties of lactide-based polymeric spinal materials. Selection of the optimal sterilization method and conditions. Bulletin of Pirogov National Medical & Surgical Center. 2026;21(4):93-98. (In Russ.) https://doi.org/10.25881/20728255_2026_21_4_93